Wednesday, June 29, 2016

Carprog full V9.31airbag functions vehicle list


CARPROG FULL V9.31 (with all 21 items Adapters),
1.was designed with regard to demands of our customers to have universal tool for car radios, dashboards, immobilizers repair including advanced functions like EEPROM and microcontroller programmer.
2. Support Airbag Reset Function Well
Carprog Full Airbag:

Saturday, June 25, 2016

Carprog error: Antena not connected (SOLVED)


Nice!! Hi, all!! Happy to share this for you all, for I just succeeded to solve my Carprog with error Antena not connected.
Background:
Days ago, I bought Carprog at www.uobdii.com from China. I put antena into Carprog clone and choose toyota key, put trannsponder into antena and read ok but i chose transponder vag key show me “antena not connected”.
Ps. Here is the connection diagram, and I connected the device to the power via USB cable. All I did is according to the user manual.






Solutions!!
Yesterday I did a little research around transponder section of carprog hardware, because i always got the message – antenna not connected when i tried to read a key with transponder. I found the datasheet for HTRC110 – this is the ic that is responsible for communication with transponders through its antenna. The antenna is a simple coil, and it should form a serial lc circuit with the capacitors soldered on the PCB. The antenna’s inductance (i measured mine) is 283 µH. To form a serial resonant circuit at 125 khz we need a capacitor with approximately 6 nF (i put in my carprog a 7.4 nF because that was what i found). Now my China Carprog clone is reading the transponder (i have only one from my caddy).
Here are the mods i did:
1. replaced 150k with 15k (resistor)
2+3+4 here we need to solder a capacitor with aproximately 6-7 nF(put one or combine from 2-3 capacitors)
5. removed 100 nF capacitor
6. removed 100 pF capacitor
in position 2 it was a 2.8nF capacitor
in pos 3 it was 0.5 nF cap
in pos 4 it was 100 nF cap




Hope this helps you all.

Thursday, June 23, 2016

feedback Chinese Ucandas, Launch, Carprog, VCM and HDS




UCandas:
I have ucandas they recently roll out the 2015 update for GM and it’s very up to date on Ford. I scanned 2014-2015 Fords before with it. Its somewhat ok on SRS.
I have had success with Chrysler 300cc when snap on tool diag car as dpf problem when infact ucandas diag correct as egr, also merc slk airbag it diagnose car good
I got ucandas when first came out and it used to diag nissan very good until i did firmware update, I even have the first disc they sent with tool before they had the online register service.
It’s not a bad scanner…They use to listen to me and take my input.I love the wireless scan..and since they actually listen to me and been adding seat cal for most of the car its gotten better.
They are very outdated on Nissan thought…up to 2011…I have my eye on the GreenDS GDS+ 3, updates for Autel is a B****.
Launch
Trust me get the x431, great tool
the good thing about launch compared to autel is that launch has been on the market for very long time and they have updates all the time, ive had it for years and there really good for that compared to autel which i believe copied software for launch once and is good but they never update anything, very seldom updates.
seriously I have lots of oem scantools but use launch sometimes even on those cars when I dont feel like booting up the oem scan tool, new ford srs no problem, new nissan srs no problem, new gm srs no problem, vag, porsche, hyundai, kia no problem, only thing i wish it did was seat calibration for the hyundai kia but you can’t ask for everything, mitsubishi no problem for airbag, for the money its a steal for what it does.
Carprog
Carprog is one of the best but its not the greatest for GM cars..its great for fords with its ability to read most of them through obd port. carprog do have a obd cable to clear GM airbags but its only for some of them between 2001-2005…

Don’t expect carprogs built in crash cleaners to have a lot of coverage expecially if you are in USA…I rarely use it for that.
But my most used tool is always good old UPA. Also have X-prog box, ETL for H8SX ans SPC/MPC stuff……no one tool will do it all
As for diagnostics Launch is good start just dont go for diagun…it’s to finicky for every day shop use, i droped mine and it broke.
Depends how much work you do and how deep into you get but none of those do it all uiversal scanners can really do everythng…i used to have launch. If you have AVDI it works as an interface for a lot of OEM software (I use toyota, subaru, kia/hyundai, volvo)….good quality Ford VCM from china works just like original, there is some good quality benz and BMW units out there, vag com and VCP for vag, hicom is supposed to be good for kia/hyundai (havent tried it, will probably get it soon), Honda HDS interface is very cheap from china and latest software can be found online and works great never failed me….

Wednesday, June 22, 2016

Carprog Ecu chip tunning v8.21 ONLINE airbag reset vehicle models

Carprog v8.21 is verified OK to work online, including airbag reset, dashboard programming, immo (read pin code), MPU & EEPROM programming, radio decoding for the most Carprog multiplexers among all versions.

Carprog software:
– V8.21, needs activation but you will automatically get token renew after it used up.
– V9.31, free, no activation.

Car prog v8.21 update info:
– support new Audi dash and new airbags
– much more authorizations (more models)
– more OS options: Win XP,Win7,Win8,Win10 32-bit

Top 3 reasons to get Carprog v8.21 full:
– first carprog to support ONLINE function
– support the MOST MODELS
– come with Carprog v8.21 online-version software and FREE Carprog v9.31 offline-version software

HQ Carprog PCB:







Carprog 8.21 software display:




Carprog performs well in airbag reset:


S5.1 – VAG (for Audi, VW, Skoda, Seat) Airbag Reset Tool
S5.2 – for BMW Airbag Reset Tool
S5.3 – for Mercedes Benz Airbag Reset Tool
S5.4 – for FORD Airbag Reset Tool
S5.5 – for GM Airbag Reset Tool by OBDII
S5.6 – CARPROG CR16 Airbag tool – for Audi, Mercedes, Ford, Volvo
S5.7 – for Renault Airbag reset tool
S5.8 – for Peugeot Airbag Reset tool
S5.9 – for Citroen Airbag Reset tool
S5.10 – for Honda Airbag Reset tool
S5.11 – for Audi Airbag reset tool by direct connection to EEPROM or MPU
S5.14 – for Ford Airbag Reset tool by direct connection to EEPROM or MPU
S5.16 -for Hyundai Airbag Reset tool
S5.17 – for KIA Airbag Reset tool
S5.18 – for Lexus Airbag Reset tool
S5.19 – for Rover Airbag Reset tool
S5.21 – for Mazda Airbag Reset tool
S5.22 – for Mitsubishi airbag reset tool
S5.23 – for Nissan Airbag reset tool
S5.20 – for Mercedes Benz Airbag Reset tool by direct connection
S5.25 – for Opel Airbag reset tool by direct connection
S5.27 – for Saab Airbag reset tool by direct connection
S5.28 – for Subaru Airbag reset tool by direct connection
S5.30 – for Toyota Airbag reset tool by direct connection
S5.31 -for Alfa Romeo Airbag Reset Tool
S5.32 – for Fiat Airbag Reset Tool
S5.33 – for Porsche Airbag Reset Tool
S5.34 – Suzuki Airbag Reset Tool
S5.35 – for Volvo Airbag Reset Tool
S5.36 – for Daewoo Airbag Reset Tool

http://www.uobdii.com/wholesale/carprog-full.html 
post on http://carprog-carprog.blogspot.com

Friday, June 17, 2016

How to solve Carprog Full v7.28 tokens run out

Caprog full v7.28 airbag reset tool tokens run out,device not in use problem solution is provided.

Problem:
My Carprog full v7.28 has run out tokens and stop working. How to solve the problem?

Thursday, June 16, 2016

How to update Carprog Clone to V8.03 (customer feedback)

Here’s the customer solution to update Carprog full v7.28 China Clone ECU, car radios, Airbag, dashboards, immobilizers repair kit to new 8.03.

Wednesday, June 15, 2016

Carprog full errors “Damaged parts -6 or 4”(solved!)

These are customer solutions to Carprog full V7.28 errors “Damaged parts -6 or 4” with detailed information like “Damaged parts – ARM7 +4 ARM7(master mcu) can’t be replaced contact seller to repair your device.”

Error:
Damaged parts -6
Damaged parts -4
Error message:
Damaged parts – ARM7 +4 ARM7(master mcu) can’t be replaced contact seller to repair your device.


Damaged parts -6
Demaged part -6 means you have broken mcz33290(ISO K Line Serial Link Interface)


If you look at 2 pictures when you click HW test you can see some ic-s with numbers on it, under 6 is mcz33290. You can take it from D1 adapter just for probe – there is mc33660 – its the same;



When the Carprog full  interface came with a problem “Demaged part -6”, tested with A9 and all was ok then.

Damaged parts -4
had a problem with my Carprog clone when connect it to computer and push “Hardware test”. the result is error in some “PIN” a final error is “Damaged 4 parts”.


Now make the A9 Adapter and everything will be OK in the end









Maybe, some guys may be unlucky if even do so. And that is another possible reason:
the Voltage is too large and heat is not good —> overheating then burn the 4th mcu chip. Replace the 4th chip using a heat gun or sent it back to seller to repair your carprog full.
NOTE: solutions above is from caprog users. You may be at risks to try it. UOBD2 just offers information here but won’t be responsible for it. Good luck!
Carprog full set cables

Tuesday, June 14, 2016

Free download Carprog full V7.28 China Clone

Carprog full China clone Airbag reset, Odometer, Radio, Mileage, Dashboard, Immobilizer, Transponder programmer V7.28 software can be downloaded free here.

Software version: V7.28
Operating system: Windows XP (without anti-virus)

Carprog full v7.28 clone software free download
http://www.chinaautodiag.com/download/carprog%207.28.zip

Software including:
ECU-OPEL – OPEL login reader from motor hybrid ECU. Works with Bosch ME1.5.5, Siemens SIMTEC71, SIMTEC71.1, Delco Diesel, Delco Multec.
OPEL CAN – Opel ECU by CAN programmer – read/change mileage in EDC16, MT35E, HSFI 2.2 read PIN, reset ECU
PSG16 – Opel PSG16 diesel pump by OBDII – read/change mileage, read PIN, reset ECU
OPEC28 – Opel Siemens Simtec ECU Tool Advanced

Carprog full Airbag: 
S5.1 – VAG (Audi, VW, Skoda, Seat) Airbag Reset Tool
S5.2 – BMW Airbag Reset Tool
S5.3 – Mercedes Benz Airbag Reset Tool
S5.4 – FORD Airbag Reset Tool
S5.5 – GM Airbag Reset Tool by OBDII
S5.6 – CARPROG CR16 Airbag tool – Audi, Mercedes, Ford, Volvo
S5.7 – Renault Airbag reset tool
S5.8 – Peugeot Airbag Reset tool
S5.9 – Citroen Airbag Reset tool
S5.10 – Honda Airbag Reset tool
S5.11 – Audi Airbag reset tool by direct connection to EEPROM or MPU
S5.14 – Ford Airbag Reset tool by direct connection to EEPROM or MPU
S5.16 – Hyundai Airbag Reset tool
S5.17 – KIA Airbag Reset tool
S5.18 – Lexus Airbag Reset tool
S5.19 – Rover Airbag Reset tool
S5.21 – Mazda Airbag Reset tool
S5.22 – Mitsubishi airbag reset tool
S5.23 – Nissan Airbag reset tool
S5.20 – Mercedes Benz Airbag Reset tool by direct connection
S5.25 – Opel Airbag reset tool by direct connection
S5.27 – Saab Airbag reset tool by direct connection
S5.28 – Subaru Airbag reset tool by direct connection
S5.30 – Toyota Airbag reset tool by direct connection
S5.31 – Alfa Romeo Airbag Reset Tool
S5.32 – Fiat Airbag Reset Tool
S5.33 – Porsche Airbag Reset Tool
S5.34 – Suzuki Airbag Reset Tool
S5.35 – Volvo Airbag Reset Tool
S5.36 – Daewoo Airbag Reset Tool




3. CarProg Dash:
S7.1 – VAG CAN programmer
S7.2 – CarProg Dashboard programming
S7.3 – CarProg Dashboard programming package update
S7.5 – Mercedes Benz ASSYST explorer
S7.6 – VDO dash decrypt tool – Skoda Roomster, SuperB, VW Polo, Audi A3, A6, Allroad with 93C86 odometer change and PIN reading
S7.7 – Ford odometer change by OBDII (by CAN)
S7.8 – VW 2007+ by OBD – Golf, Passat, Eos, Touran, Tiguan, Octavia with Micronas by diagnostic
S7.10 – VAG VDO dashboards by K-line OBDII diagnostic – VW T5, Passat B5, Skoda SuperB and others
2J74YAUDI – Audi 2J74Y repair software for CarProg


4. CarProg Immo:
S4.1 – Toyota Key Programmer
S4.2 – Lexus key programmer
S4.3 – Daihatsu Key Programmer
S4.4 – CarProg BMW Key programmer
S4.5 – Mercedes Benz Key programmer
S4.6 – RENAULT Megane/Scenic infrared key programmer
S4.7 – Kessy tool – A8, Touareg, Phaeton, Cayenne PIN code reader

5. CarProg Processor:
S2.1 – CARPROG Motorola (Freescale) HC05 MPU programmer
S2.2 – CARPROG Motorola (Freescale) HC11 MPU programmer
S2.3 – CARPROG Motorola (Freescale) HC08 MPU programmer
S2.4 – CARPROG Motorola (Freescale) 912 and 9S12 MPU

6. CarProg 7.28 Programmer:
ST92 – ST92F120, ST92F150, ST92F250 internal EEPROM programmer

7. CarProg Radio Code:
S6.1 – CARPROG CC1
S6.2 – CARPROG CC2
S6.3 – CARPROG CCN
S6.4 – Philips Car Radio decoder
S6.5 – Renault Car Radio decoder by serial number
S6.6 – Audi/VW/Seat/Skoda car radio decoding software
RNS510 – Navigation decoding tool by Navi diagnostic




CarProg full 21 Adapters:
1: CarProg Main harware interface
2: A1 – OBD2 Adapter Cable (Inside have K-line and CAN bus switches. Use with all cars complained with OBDII standard)
3: D1 – Odometer-airbag Adapter  (Dashboard ,Airbag programming adapter )
4: A3 – Transponder Antenna ( Used with all CARPROG immobiliser software )
5: A10 – Motorola Adapter Cable  (Motorola MCU programing adapter )
6: A11 – BMW EWS Adapter Cable   ( Used with BMW Immo software )
7: A16 – Car radio Cable   ( Used for Opel, Renault, Peugeot, Citroen car radio made by Philips decoding)
8: A15 – Cable  (Used with D1 adapter ,Universal car dashboard and airbag programming adapter )
9: A17 – Honda Airbag OBD2 Cable  (Adapter for Honda airbag reset by OBDII )
10: A4 – Eeprom Adapter Cable   (Used for eeprom programming)
11: A5 – DIP8 Clip Cable   (DIP8 Clip for eeprom programming)
12: A6 – SOIC8 Clip Cable   (SOIC8 Clip for eeprom programming)
13: A7 – MB 38-Pin Cable   (Used with MB Airbag and dashboard software)
14: A8 – BMW 20-Pin Cable (Used with BMW airbag and dashboard software )
15: RNS510 Adapter Cable  (RNS510 radio decoding interface cable )
16: VOLVO FORD CAN 2006+ Cable   (Needed for airbag and dashboard programming)
17: FIAT CAN 2006 Cable   (Needed for airbag and dashboard programming)
18: C1 OBD2 Female Cable
19: USB Cable
20: Power cable
21: CD   (Software V7.28)

Monday, June 13, 2016

How to use Carprog v9.31 to read and erase BMW EEPROM M35080

Free download Carprog full v9.31 software shared by a forum member and tested on BMW EEPROM M35080.. No issues.

Carprog 9.31v software i used on Windows XP operating system:
https://mega.nz/#!QF4D2ajZ!sew7H0E2wZeo7bfNdM3XJn4yN8i2BZGQ1u4nmR-O3dA

Sunday, June 12, 2016

Carprog V8.21 activate on Win7 instruction

Today UOBD2II.COM Enginner tell you how to install and active carprog v8.21 on Win7 .

Software version: V8.21
Free download carprog v8.21 perfect online software (Disable anti-virus software)
Optional operating system:
Windows XP, WIN7, WIN8, WIN10

Saturday, June 11, 2016

Carprog full V8.21and Carprog full V9.31 Software free download

New Carprog full V8.21 firmware perfect Online version with all 21 adapters including much more authorizations and free carprog v9.31 software is available in UOBD2.NET

Software version:
V8.21, needs activation but you will automatically get token renew after it used up.
V9.31,free, no activation.
Operating system: Win XP,Win7,Win8,Win10 32-bit

Friday, June 10, 2016

FREE CarProg v8.21 v9.31 – Cracked! No pass! Test OK!


Free reliable and tested Carprog v8.21 and Car prog v9.31 full software here.
Free download Carprog software
Carprog v9.31:
http://www.chinaautodiag.com/download/carprog-9.31.zip (Activated!)
Newest!
FREE!
NO Pass!
Cracked!
Tested with Carprog clone like:
http://www.uobdii.com/wholesale/carprog-full.html

Thursday, June 9, 2016

Carprog v9.31,Carprogv8.21and Carprog V7.28 Comparison table

Recently,UOBD2 issue newer Carprog v9.31 and v8.21.Caprog v9.31 is the latest version with the plug-and-play feature and no need activation, while Carprog 8.21 highlights the online feature and the most vehicle coverage.

Tuesday, June 7, 2016

How to Solve China CARPROG CANBUS Not Working?

This is a customer solution and feeback on China Carprog 7.28. He has successfully deal with “CARPROG CANBUS no working” issue.

I buy china carprog and coming sames problem CANBUS NO WORKING. I changing around 3x MCP not working, Conecting +12 volt to stabilizer not working, changing 4x 74HC125 in carprog not working. so i thinking around this tool and i open A1 adapters and compared with original A1 adapter .
I FIND WHERE IS PROBLEM !!!!
In china peoples changing positions CAPACITORS AND RESISTORS !!!!.
I forget on important information IN A1 ADAPTER IS NOW SOLDERED NEW MCP old MCP. i dont soldered back. i dont tested ODL MCP if work wit this or not. So far, it is WORKING GOOD.


I forget on PRT SCR from my china carprog conected to opel can.


CARPROG full 7.28 (Best Quality)

Monday, June 6, 2016

CARPROG Full ECU Chip Tunning Feedback

This post collects all of available customer feedback on CARPROG Full ECU Chip Tunning. Hope it helps!


  1. CARPROG works with both solution, odb and welding to read the EPROM.
some airbag crash can be repaired by obd but in general we have to and passed by the box desoldering of EPROM. the advantage, it has a database of clear crash for some model, an original radio code generator; this is a good program to start.
CARPROG full v7.28 with everything and explained in the software, and it comes with several
connectivity number. As selecting a function that we want to use it tells us what connectors used.
It is even illustrated with photos very nice.Car Key programemr
2.
For me, it’s not bad to begin with, the basic equipment (hot air station, flux pen, soldering iron with a fine tip) ismandatory to exploit
3.
Beginners opt for CARPROG.It offers a lot of opportunity, it does not cover all but a good party. Simple handling,intuitive app. it is polivalent dash, immo, radio ..
4.
I used to virginiser of BSI, I also managed to modify a 2002 vehicle en dash (just to test, Idelivered as it was before)
I also managed to lire OF 5p08 (95p08) and write off properties not bad for beginners, less effective than XPROG or UPA but easier to use.
good flash
5.
Question: You have a merchant recommend? a Chinese version is it the case?
Reply:http://www.uobdii.com/wholesale/carprog-full.html
They are well and have a very proper customer relationship

Question: You mean the clone or the original? Because the budget is not the same … And the clone functionality level, we can estimate how many percent compared to the original (if quantifiable)? Gadget or good tool to start?

Reply: It is 40% of the original on the radio codes ok but the dashboard there is not any lack of image the rest is a very fragile CARPROG use it after several silliness more communication with the interface, it must be used with a PC without internet with a stable and xp ca va …
Super good tools began frankly I’m very happy easy to use but it’s still the lolll brol as a tool that makes
http://blog.uobdii.com

several operations:
-airbag
-code radio
-Immo
-counter
-ecu opel
-some ePROM
-some mcu
(A tool that helps you one day is priceless …)

This article from:http://carprog-carprog.blogspot.com